Skip to main content

Soil Moisture sensor with Arduino in Tinkercad | how to use soil moisture sensor in Tinkercad

  Soil Moisture sensor with Arduino in Tinkercad | how to use soil moisture sensor in Tinkercad Circuit diagram: Arduino Sketch: // C++ code // int moisture_data = 0; void setup() {   pinMode(A0, INPUT);   Serial.begin(9600);   pinMode(12, OUTPUT);   pinMode(6, OUTPUT); } void loop() {   moisture_data = analogRead(A0);   Serial.println(moisture_data);   if (moisture_data < 21) {     digitalWrite(12, HIGH);     digitalWrite(6, HIGH);   } else {     digitalWrite(12, LOW);     digitalWrite(6, LOW);   }   delay(10); // Delay a little bit to improve simulation performance }
1 comment

LED Blink Using an Arduino in Tinkercad

 Tutorial No:-01 LED Blink Using an Arduino in Tinkercad

Let’s connect an LED. LED stands for Light Emitting Diode. If you connect the LED directly to power and ground, too much current will go through the LED and Burn it. To avoid  that from happening we will usea The resistor is the part of an electrical circuit that resists, or limits, the flow of an electrical current in a circuit The resistance of a resistor is measured in ohms. The symbol for an ohm is the Greek capital-omega: Ω. We will use a 270 ohm. Resistors have color bands on them we can calculate the valuve of resistor using the colour bands. Resistor has two legs without polarity and actually It doesn’t matter which way you plug in a resistor.The two terminals of an LED are called an anode and a cathode. The anode is the longer end and shorter end is cathode.

Circuit Diagram:


Program for LED blinking:




Like share and comment :

                                                     Our FaceBook Page                                                           



Our Youtube Channel.




For Any queries please contact:

impulseTech101@gmail.com

Comments

Post a Comment

If you any query please comment

Popular posts from this blog

Soil Moisture sensor with Arduino in Tinkercad | how to use soil moisture sensor in Tinkercad

  Soil Moisture sensor with Arduino in Tinkercad | how to use soil moisture sensor in Tinkercad Circuit diagram: Arduino Sketch: // C++ code // int moisture_data = 0; void setup() {   pinMode(A0, INPUT);   Serial.begin(9600);   pinMode(12, OUTPUT);   pinMode(6, OUTPUT); } void loop() {   moisture_data = analogRead(A0);   Serial.println(moisture_data);   if (moisture_data < 21) {     digitalWrite(12, HIGH);     digitalWrite(6, HIGH);   } else {     digitalWrite(12, LOW);     digitalWrite(6, LOW);   }   delay(10); // Delay a little bit to improve simulation performance }
1 comment
Read more

Getting Started with the Arduino IoT Cloud using Esp32 & DHT-11

  Getting Started with the Arduino IoT Cloud using Esp32 Introduction: The Internet of Things has given rise to plenty of exciting new projects for makers. It's both interesting and practical to be able to develop remote sensors and gadgets. Allowing IoT devices from multiple manufacturers to interact with your innovations will open up a lot of possibilities, including some you might not have considered before. In this getting started guide of Arduino IOT cloud we will learn about how to use Arduino IOT cloud with Esp32 board. Arduino IOT cloud What is Arduino IOT cloud? Arduino IoT Cloud is a web-based service that allows users to create connected devices quickly, easily, and securely. Multiple devices can be linked together and data can be exchanged in real-time. Users can also able to monitor the data using a simple user interface from anywhere. one can also use the android application for monitoring and controlling the devices. Because Arduin...
Post a Comment
Read more

Interfacing of TMP36 Temperature Sensor with an Arduino in Tinkerad.

  Interfacing of TMP36 Temperature Sensor with an Arduino in Tinkerad. This project will turn the Arduino into a thermometer! By using the tmp36 temperature sensor. We can able to measure our body temperature and turn on the 3 LEDs. Green LED indicates the low-temperature range, Yellow LED indicates the medium temperature range and Red LED indicates the high-temperature range. One can test the circuit starting the simulation, clicking on the sensor, then adjusting its temperature value using the slider, and can test the desired resulting LED patterns. For making the actual circuit, you need to use the Arduino, breadboard, USB cable, male-female jumper wires, three LEDs, three resistors (any value from 100-1K, 220 ohms), a TMP36 sensor,   Circuit Diagram:   Components Required: §   Arduino UNO §   TMP36 (Temperature sensor) §   Resistor-03 §   LED – Green §   LED – Yellow § ...
1 comment
Read more